A
USERS GUIDE
TO
AIRCRAFT
RADIO
CORPORATION
RECEIVERS

by
M. W. Tauson

One of the neat things about the military is the rather vast quantities in
which it produces surplus for people like us to pick up in equally vast
quantities. This process has most likely been going on since Ceasar's time
(although I suspect the market has probably changed a bit) and will continue as
long as there are militaries to have surplus.

Probably the one group of radio equipment to hit the market more heavily than
any other is that known as the Command sets. These units (specifically the
ATA/ARA, SCR-274N, and ARC-5 sets) were released as surplus after World War II
and are still showing up in new, unused condition some 35 years later. They have
been converted from mild to wild and are responsible for getting quite a few
people on the air who could not have otherwise afforded a rig, myself included.

The original design that started this avalanche came from Aircraft Radio
Corporation. There were three major builders, A.P.C., Stromberg-Carlson who
built most of the early ATA/ARA sets as well as some of the ARC-5's and later
Type 12's, and Western Electric who built most of the SCR-274N's (Navy rigs with
Army markings essentially) plus the VHF Command sets. There were other suppliers
but not any that produced the quantities that these did.

As a general rule, SCR-274N and ATA/ABA equipment may be mixed freely. ARC-5
receivers may be used with the other two series, as may the racks, control
boxes, etc. ARC-5 transmitters, modulators, racks and control boxes for the
transmitters will not mate with their counterparts due to connector differences.
It is interesting to note that the various receivers would also fit the SCR-274N
and ATA transmitter racks which probably lead to the early (if not smelly)
demise of a few receivers, and played a part in the design change for the ARC-5
transmitter rack.

The A.R.C. type 15 receivers will fit the Command set racks however the pin
assignments are different necessitating some re- wiring. The Type 12 receivers
and the TV-10 transverter also fits however there is no rear connector on them
nor is there any method to lock them in place. The modifications are very simple
however and it does make for a convenient way to mount the unite.

The various control boxes are useful not only for controlling 'in type'
equipment but also for other pieces.

The information on the following pages is from tech manuals, schematics and
in some cases from the units themselves. There are no schematics- these are
available from such sources as the nice people at Fair Radio Sales. What is here
is some very basic info on 'What is it?' and 'How do I make it work?'. There are
equipment lists, pinots, some VERY brief specs, connector lists, and a few quick
hook-ups so you can light off the rig without too much fuss and bother.

Some pieces not in the Command and Type 12 series are included, and some that
are parts of the various series are not here. The criteria for these two groups
was availability- the former are generally available and the latter aren't.

Where possible, included the A.R.C. part number for the various units, which
provides a ready made cross-reference between the series. There are at the end a
series of lists in numeric order to assist in this referencing.

The ATA/ARA and some pieces of the ARC-5 sets are identified by a five digit
number. This is the numeric portion of the Navy accounting number of the item.
The Navy accounting system is a method of uniquely identifying equipment and
consists of a three letter and five digit code. The three letters (the first of
which is always 'C') identifies the builder, with CBY (A.R.C.) and CCT
(Stromberg-Carlson) being the ones most commonly found on the Command set units.
The first two digits of the numeric portion identify the type of unit (46 for
receivers, 52 for transmitters, etc with related pieces carrying the same type
identifier) and the last three digits uniquely identify the particular unit.
Note that a CBY-46104 receiver and a CCT-46104, for example, are the same
receiver built by two different builders. For this reason, the builder code has
been deleted from the following lists.

The builder code does appear on some, if not all, ARC-5 units on the
identification plate after the serial number. On the other series, the builder's
name often is on the identification plate at the bottom.

At some point or another, I hope to have an addendum covering items missed
plus any added information that may be of use. Any assistance toward this end
will be gratefully accepted, and will be acknowledged in the addendum. In the
mean time, however, I would like to thank George Sellout at Fair Radio for his
help (and for being tolerant of me!), Gordon Eliot White for getting me
interested in A.R.C. through his many fine articles, and, of course, the
Aircraft Radio Corporation for their excellent products which have brought many
hours of pleasure.

EQUIPMENT LISTS

The equipment lists are broken into four groups, SCR-274N & ATA/ARA,
AFC-5, Type 12, and Miscellaneous. Some very minor specs are presented on the
receivers and transmitters and, where possible, A.R.C.'s part number is given.
To assist in locating a particular piece, the lists are broken into
sections-Receivers, Transmitters, etc.

SCR-274N, ATA/ARA

Receivers

Identification
Freq. RNA SCR-274N Navy (ARA) IF Sense Select(kHz)
(MHz) Mil ARC# Mil ARC# (kHz) (uv) 3db lOdb
.19 - .55 BC-453 7594 46129 7839 85 7 1.7 3.1
.52 - 1.5 BC-946 46145 5950 239 8 2.9 4.9
1.5 - 3.0 .... 46104 5005 705 6 3.9 6.4
3.0 - 6.0 BC-454 7595 46105 5006 1415 7 7.5 12.5
6.0 - 9.1 BC-455 7596 46106 5007 2830 8 9.8 24.2

Transmitters

Identification
Freq Rng SCR-274N Navy (ATA) Power
(MHz) Mil ARC# Mil ARC# In(W)
2.1 - 3.0 .... 52232 7916 89
3.0 - 4.0 BC-696 52208 5009 88
4.0 - 5.3 BC-457 7632 52209 5010 88
5.3 - 7.0 BC-458 7633 52210 5011 90
7.0 - 9.1 BC-459 7634 52211 5012 90

Accessories

Identification
Item Name SCR-274N Navy ARC# Notes
Modulator BC-456 50083 7591 ARC # for Navy is 5013
Antenna Relay BC-442 29125 5017
Dynamotor, Rec DM-32 21531 7351 250v, 60ma
Dynamotor, Tran DM-33 21626 5168 575v, 160ma continuous
540v, 250ma intermit
Adapt., Rem Ctl FT-230 49107 6433
Adapter, Power FT-310 62036 9074 For Inst. Land. Sys.
Adapt., Lcl Ctl FT-260 - 6434

Control Boxes

Identification
Function SCR-274N Navy ARC#
Transmitter BC-451 23243 7095
1 Receiver BC-473 23261 7043
2 Receivers BC-496 23155 6546
3 Receivers BC-450 23251 5014

Racks and Mounts

Trans & Rec

Identification-Rec Identification-Trans
# Units SCR-274N Navy ARC# SCR-274N Navy ARC#
1 Mount FT-231 - 7059 FT-232 - 7061
Rack FT-233 - 7509 FT-234 - 7507
2 Mount FT-279 46085 5694 FT-227 52213 7062
Rack FT-277 46110 5018 FT-226 52212 5020
3 Mount FT-221 46150 7060 FT-262 - 7063
Rack FT-220 46149 7537 FT-276 - 7638
4 Mount FT-278 - 5696 FT-332 - 7064
Rack FT-264 - 5019 FT-331 - 6090

Other Mounts

Identification
Unit Mounted SCR-274N Navy ARC#
Modulator FT-225 50084 7058
Antenna Relay FT-229 29126 7056
Ctl Box, Trans FT-228 * 7083
Ctl Box, 1 Rec FT-235 * 7053
Ctl Box, 2 Rec FT-240 * 6831
Ctl Box, 3 Rec FT-222 * 7054

Miscellaneous

Identification
Item Name SCR-274N Navy ARC-5 Notes
Dial, .19-.55 MHz MC-214 * 6051 For ctl boxes
Dial, .52-1.5 MHz MC-415 * 6052 " " "
Dial, 1.5-3.0 MHz -- * 7575 " " "
Dial, 3.0-6.0 MHz MC-213 * 6053 " " "
Dial, 6.0-9.1 MHz MC-2i2 * 6054 " " "
Wired Plug PL-192 - 6787 Used with Lcl Ctl Adapt.
Kit, Tuning Shaft MC-215 * 6151
Knob, Lcl Tuning MC-237 - 6743 Also MC-236
Adapter, Rt angle MC-211 - 6357 For tuning shaft

* designates no unique identification assigned to this piece.

ARC-5

Receivers

Freq Rng Ident IF Sens Select(kHz)
(MHz) ARC-5 ARC# (kHz) (uv) 3db lOdb
.19 - .55 R-23 9602 85
.19 - .55 R-23A 10007 85 5 1.1 2.2
.19 - .55 R-148 10008 85 5 1.1 2.2 *12v Fil.
.52 - 1.5 R-24 9603 239 7 2.1 4.0
1.5 - 3.0 R-25 9604 705 7 3.2 6.0
3.0 - 6.0 R-26 9605 1415 6 7.3 13.0
6.0 - 9.1 R-27 9606 2830 6 13.0 26.0
100 - 156 R-28 12mHz

Transmitters

Freq Rng Identification Power
(MHz) ARC-5 Navy ARC# In(W)
.50 - .80 T-15 52302 9315
.80 - 1.3 T-16 52303 9316
1.3 - 2.1 T-17 52304 9317
2.1 - 3.0 T-18 52305 9308 106
3.0 - 4.0 T-19 52306 9309 102
4.0 - 5.3 r-20 52307 9310 107
5.3 - 7.0 T-21 52300 9311 96
7.0 - 9.1 T-22 52309 9312 99
100 - 156 T-23

Accessories

Ident
Item Name ARC-5 ARC# Notes
Modulator MD-7 9313 Navy Acct'g # is 50141
Antenna Relay RE-2 5017
Antenna Tuner TN-6 9607
Dynamotor, Rec DY-1 250v, 60ma, 12v in
" " DY-2A 7351 " " , 24v in
" " DY-2B 10009 " " "
Dynamotor, Tran DY-8 5168 575v, 160ma continuous
540v, 250ma intermit
Adapt., Rem Ctl MX-21 6433
Adapter, Power MX-20 9074 For Inst. Land. Sys.
Adapt., Lcl Ctl C-24 6434
Adapter, Audio MX-19 9595

Control Boxes

Ident
Controlled Function ARC-5 ARC# Notes
Remote Ant/Loop Sw C-25 Via mech. link to rec.
1 Rec, Tunable C-26 9601
1 Rec, Lock-tuned C-27 9850
HF Transmitters C-29 7314
HF Trans, VHF Chan C-30 Push-button Tr, Ch sel
HF Trans, VHF Chan C-30A 9910 Rotary Tran, Chan sel
Main Ctl Box C-38 9610 Recs: 2 HF lock-tuned,
1 VHF, 1ARR-2,
Trans & Rec Audio
Auxiliary Ctl Box C-39 9901 ICS/Radio Sel, T & R Audio
1 Rec, VHF C-42
3 Rec, 2 HF & 1 VHF C-43 HF Rec are Tunable
Auxiliary Ctl Box C-48 9902 As C-39, Has Mic Relay
1 Rec, Tuneable C-125 9911 Panel Mount, Like C-26
1 Rec, Tunable LF C-744 New Panel Mt, No BFO Ctl

Jack & Junction Boxes

Ident
Function ARC-5 ARC# Notes
Jack Box, Mic/Tel J-16 9905 No Vol Ctl or Mic Relay
Junct Box, System J-17 9903 For Multi-system Install.
Jack Box, Mic/Tel J-22 9867 No Mic Relay
Jack Box, Mic/Tel J-22* 9907 Has Vol Ctl & Mic Relay
Ctl Split, VHF Chan J-28 9609 For C-30* to R-28 & T-23
Ctl Split, Trans J-34 9562 For Multiple Trans Racks
On 1 Modulator

Racks & Mounts

Trans & Rec

Ident-Rec Ident-Trans
# Units ARC-5 ARC# ARC-5 ARC#
1 Mount MT-5 7059 MT-68 7061
Rack MT-7A 7509 MT-69 9306
Rack MT-411 9202 - -- Wired for 12v
2 Mount MT-62 5694 MT-70 7062
Rack MT-63 5018 MT-71 9307
3 Mount MT-64 7060 MT-72 7063
Pack MT-65 7537 MT-73 9593
4 Mount MT-66 5696 MT-74 7064
Pack MT-67 5019 MT-75 9394

Other Mounts

Ident
Unit Mounted ARC-5 ARC# Notes
Modulator MT-76 7067
Antenna Relay Mt-77 7065
Antenna Tuner MT-159 7057
Ctl & Jack Box MT-78 9451 For C-27, j-16,-22,-22'
Control Box MT-4 7053 For C-26
Ctl & Junct Box MT-80 7083 For C-29,-30,-39,-48'
J-28,-34
Control Box MT-98 7054 For C-38,-43
Junction Box MT-84 9904 For J-17

Miscellaneous

Ident
Item Name ARC-5 ARC# Notes
Dial, .19 - .55 MHz ID-25 6051 For tunable Rec Ctl Box
Dial, .52 - 1,5 MHz ID-26 6052 " " " " "
Dial, 1.5 - 3.0 MHz ID-27 7575 " " " " "
Dial, 3.0 = 6.0 MHz ID-28 6053 " " " " "
Dial, 6.0 - 9.1 MHz ID-29 6054 " " " " "
Wired Plug J-33 6787 Used With Lcl Ctl Adapter
Kit, Tuning Shaft * 6151
Knob, Lcl Tuning * 7643
Knob, Lcl Ant/Loop * 7491
Knob/Cap, Lock-tun'g * 9554
Adapter, Rt Angle MX-22 6357 Used with Tuning Shaft

* No unique identifier in ARC-5 system

Note: The following are components of the ARR-2 system that
are used with the ARC-5 system: DY-l, DY-2A, DY-2B, MT-4,
MT-5, MT-7A, MX-22.

Type 12

Receivers

Freq Rng Identification IF Sens Select(kHz)
(MHz) Civilian Mil (_Hz) (uv) 6db 60db Notes
.19 - .55 R-11(12v) P-510 85k 2 5.6 12v
R-11(24v) R-511 85k 2 5.0 24v
.52 - 1.5 R-10 239k 2 7.6 12 or 24v
108 - 136 R-15(12v) 15m 2 100. 350.0 12v
R-15(24v) R-509 15m 2 100. 350.0 24v
118 - 148 R-19(12v) R-507 15m 2 100. 350.0 12v
R-19(24v) R-508 1Sm 2 100. 350.0 24v

Transmitters

Freq Rng Identification Tubes Power
(MHz) Civilian Mil Used Out(w) Notes
116 - 132 T-11A 6AQ5 2 12 or 24v
T-11B(12v) T-336 5763 2+ 12v
T-11B(24v) T-366 5763 2+ 24v
132 - 148 T-13 6AQ5 2 12 or 24v
(see note) T-13A(12v) T-363 5763 2+ 12v
T-13A(24v) T-364 5763 2+ 24v

Note: Freq may be lowered to 125 mhz by using capacity plates
ARC# 15392 for the T-13 and ARC# 15900 for the T-13A.

Dynamotors

D-10A(12v), ARC# 14480: 12v,3.4a in, 250v,85ma out
D-10A(24v), APC# 14482: 24v,l.7a in, 250v,85ma out

Note: Dynaverter DV-10,-1OA is later replacement

Junction & Jack Boxes

Item Name Ident Notes
Jack Box J-10 Aircrew Mic/Tel
Junction Box J-12 32 Tie points. 12v
Junction Box J-13 32 Tie points, 24v
Junction Box J-15 56 Tie points, 24v

Control Boxes

Ctl'd Function Ident Notes
1 Rec C-16 Dial for R-11A
1 Rec C-17 Dial for R-15
Loop Heading C-18
3 Rec. 2 Tran. C-24 1 ea, R-lO,-ll,-15, 2 Type 12 Trans
Loop Heading, Panel Mount
3 Trans C-25 2 Type 12, 1 Extern Trans
2 Rec. 3 Trans. C-36 1 ea: R-11,-19, 2 Type 12 trans.
I Extern Trans, Loop Heading.
Panel Mount
2 Rec. 3 Trans C-37 Like C-36, No Loop or Panel Mount
2 Rec. 3 Trans C-38 1 ea: R-11,-15. 2 Type 12 Trans,
1 Extern Trans
2 Rec. 2 Trans C-39 As C-36, panel Mount, No Extern Trans
Loop Heading
3 Rec. 3 Trans C-40 1 ea: R-11,-19, Tunable HF ARC-5 Rec.
1 ea: HF & VHF ARC-5 trans, Extern Trans
Panel Mount
1 Rec. Loop Hdg C-48 Dial for R-11, Loop Heading, New Panel Mt
1 Rec. 4 Trans C-56 Dial for R-19, 3 Type 12 Trans, 1 Extern
Trans, Whistle-stop, New Panel Mount

Mounts

Unit Mounted Ident Notes
1 Transmitter M-11
1 Receiver M-12
Control Box M-13 For C-37,-38, Like ARC# 6831
Control Box M-18 For C-16,-17,-18, Like ARCF 7053
Control Box M-19 For C-25, Like ARC# 7083

Miscellaneous

Item Name Ident Notes
Antenna, VHF A-12 3-Section Rod
Antenna, Loop L-10 9" Dia, Mil, AT-382
Kit. Wire Antenna - ARC# 12296
Kit. Tuning Shaft - ARC# 6151
Wired Plug - ARC# 11934. Used when oper'g Rec
without Trans.

Related Equipment

SCR-274N, ATA/ABA

Receiver Test Set-up, ARC# 7918 (Mil: RC-54A)
Consists Of: 7369 Meter Panel, Single Rec Rack & Mount,
Dynamotor, Tuning Knob, and Cables
Transmitter Test Set-up, ARC# 7919 (Mil: RC-55A)
Consists of: 7507 Meter Panel, Single Trans Rack & Mount,
Modulator & Mount, Dynamotor. Ctl Box, Cables,
and ARC# 7777 Dummy Ant. (Mil: A-61A)

ARC-5

Receiver Test Set-up (as SCR-274N, ATA/ARA)
Transmitter Test Set-up, ARC# 9558
Consists of: 9556 Meter Panel, Crystals for 3, 4, 5.3,
7. & 9.1 MHz and contents of ARC# 7919 Set-up.
R-4/APR-2 Homing Receiver, 234-258 MHz
Includes: C-2/APR-2 Ctl Box (if rec is used alone.)
MX-2/ARR-2 Wired Plug for Rec Rack

A.R.C. Type 12

R-20 Fixed-tuned (75 MHz) Marker Beacon Rec
R-22 .55-1.5 MHz Rec (Like R-10 but later model)
R-836 .19-1.75 MHz ADF Rec, Part of ARN-59 System
Includes C-2275/ARN control Box
TV-10 (CV-431/AR) Transvertor
Trans: 228-258 MHz, Converts 228-258 MHz to 118-148 MHz Rec.
Type 15 Equipment (VOR/ILS Receiving Eq't)
R-13 (R-445/ARN-30) 108-136 MHz Rec.
R-34 (R-1021/ARN-30D) 108-126.9 MHz Crystal-ctl'd Rec
B-13 (CV-265/ARN-30) VOR/ILS Converter
E-14 (MT-1175/ARN-30) Equipment Rack
C-81,-88 Control Boxes For R-34
C-3436A/ARN-30 Ctl box for R-1021/ARN-30D

PINOUTS

On the following few pages are pinouts for the connectors on most of the
equipment previously listed. The same order of categories is preserved as used
in the previous section however they are collected so that all the receivers are
together, etc for the main equipment. The related equipment is still separate
and at the end of the section.

Except for two cases, all the connectors are numbered anticlockwise when
viewed from the outside. The exceptions are the connectors on the rear of the
rack-mounted receivers and transmitters, and those on the rear of the receiver
adapters.

The number in parenthesis is A.R.C.'s part number for the receptacle in
question. The 'Connectors' section following this one is ordered numerically on
this number, and can be used to locate the proper plugs to match.

Notes are indicated by an asterisk and a one or two digit number (for
example, *4 or *28.) The notes are at the end of the section. The number refers
to a particular note.

An Asterisk used as a suffix to a unit's identifier means that all versions
of the unit are being referenced. For example J-22- refers to the J-22, J-22A,
and J-22B.

Receivers

Command Receivers (All Series)
J-1 (4724) To Adapters *8
1 Gain Ctl 4 Nav Audio *1 7 +LV Source Out
2 Gnd 5 CW Shut-off 8 +HV Out
3 n/c 6 +LV to Rec

J-3,-102 (5488) To Rack
1Gnd 4 CW Shut-off *7 7 +HV out
2 Audio Out 5 +Vscr out *8
3 Gain Ctl 6 +LV Source In

J-103 (5577) To Channel Select Ctl Box *9
1 Sel Chan A 3 Gnd 5 Sol Chan D
2 Sol Chan B 4 Sol Chan C 6 n/c

A.R.C. R-10,-ll
J-502,-602 (12427) To Primary Power Source
A +LV Source In B Gnd

J-503,-603 (11905) To Rec Ctl Box
A Audio Out C Gnd E Sons
B Loop Relay D +LV to Rec F +LV Source Out

J-506,-606 (11905) To Transmitter *2
A +HV to Trans C Gnd E +HV to Rec
B Audio Out D +LV to Trans F n/c

A.R.C R-15,-19
J-lO1,-301 (12427) To Primary Power Source
A +LV Source In B Gnd

J-102,-302 (11905) To Rec Ctl Box
A Audio Out C Gnd E Sons
B Audio Hi-Lo D +LV to Rec F +LV Source Out

J-103,-303 (11905) To Transmitter *2
A +HV to Trans C Gnd E +HV to Rec
B Audio Out D +LV to Trans F n/c

Transmitters

SCR-274N, ATA
J-64 (5488) To Rack
1 Gnd 4 P.A. Vscr 7 P.A. B+
2 P.A. Grid 5 Select (key)
3 Osc B+ 6 +LV In

ARC-5
J-69,-308 (9302) To Rack
1 n/c 4 Gnd7 P.A. 5*
2 Osc B+ 5 +LV In
3 Select (key) 6 P.A. Vscr

J-79 (9849) To Antenna Tuner *3
1 Select (key) 2 Gnd 3 +LV Out

J-309 (7026) To Channel Select Control *10
1 Sel Chan A 4 Gnd 7 Voltage Reg.
2 Sel Chan B 5 Sel Chart D 8 n/c
3 Sel Chan C 6 Key

J-307 (6418) To Test Set *10
1 Osc Ig 4 Gnd 7 +LV
2 1st H.G. Ig 5 P.A. Ig 8 +HV
3 2nd H.G. Ig 6 P.A. Ik

A.R.C. T-11(),-13()
J-204,-404,-2302,-2402 (11905) To Rec
A +HV to Trans C Gnd E .HV to Rec
B Rec Audio In D +LV In F +LV Source

J-205,-405,2306,-2406 (12093) To Audio
A Mic In C Gnd
B Key D Tel Out *4

J-207,-407,-2303,-2403 (12097) To Ctl Box
A Sel Chan 1 D Gnd G +LV to Ctl Box
B " " 2 E Sel Chan 4 H +LV In
C " " 3 F " " 5 *5

Accessories

Modulator (SCR-274N, ATA/ARA)
J-52 (5577) To Rec Rack
1 Sidetone Inject 3 Gnd 5 Key
2 n/c 4 n/c 6 +LV

J-53 (7024) To Primary Power Source
1 +LV Source In 2 Gnd 3 +LV Source In

J-54 (7027) To Control Box
1 Sel Trans 1 7 Gnd 13 Modulator Cath.
2 " " 2 8 Mic 14 1000-cycle Off
3 " " 3 9 Key 15 +LV to Eq't
4 " " 4 10 Voice Sidetone 16 Voltage Reg.
5 Meter + 11 Tone Sidetone 17 Sidetone Inject
6 Meter - 12 Dyn. Relay 18 +LV Source Out

Modulator (SCR-274N, ATA/ARA), Con't
J-58 (7025) To Trans Rack
I Meter + 5 Gnd 9 Sel Trans 1
2 Meter - 6 Sel Trans 4 10 P.A. B+
3 Key 7 " " 3 11 0sc. B+
4 +LV 8 " " 2 12 P.A. Vscr.

Modulator (ARC-5)
J-52 (5577) To Rec Rack
1 Sidetone 1 3 Gnd 5 Key
2 A-Tel 4 B-Tel 6 +LV

J-53 (7024) To Primary Power Source
1 +LV Source In 2 Gnd 3 +LV Source In

J-70 (9417) To Trans Rack
1 +LV 5 Sel Trans 3 9 +HV
2 Sel Trans 1 6 " " 4 10 Osc. B+
3 " " 2 7 Key 11 Test Relay
4 Gnd 8 P.A. B+ 12 P.A. Vscr.

J-74 (7026) To External Equipment
1 Mic 4 Gnd 7 Key
2 A-Tel 5 Sidetone 1 8 +LV
3 B-Tel 6 Sidetone 2

J-78 (5571) To Ctl Box
1 Sel Trans 1 7 Gnd 13 Modulator Cath.
2 " " 2 8 Mic 14 l000-cycle Off
3 " " 3 9 Key 15 +LV To Eq't
4 " " 4 10 Voice Sidetone 16 Voltage Reg.
5 n/c 11 Tone Sidetone 17 Sidetone Inject
6 Sel Common 12 Dyn. Relay 18 +LV Source Out

Antenna Relay (All Series)
J-61 (7023) To Trans Rack
1 Key 3 Gnd 5 Meter -
2 Meter + 4 +LV In

Antenna Tuner (ARC-5)
J-1601,-1602 (9849) *11
1 Key 2 Gnd 3 +LV In

Remote Ctl Adapter (SCR-274N, ARA, ARC-5)
J-31 (6063) To Rec Adapt. Cavity
1 n/c 4 n/c 7 jmpr to 6
2 n/c 5 n/c 8 n/c
3 n/c 6 Jmpr to 7

Power Adapter (SCR-274N, ARA, ARC-5)
J-29 (6076) To Rec Adapt. Cavity
1 n/c 4 n/c 7 +LV (Jmpr to 6)
2 Gnd 5 n/c 8 +HV
3 n/9 6 +LV (Jmpr to 7)

J-30 (2226) To External Eq't
25 +LV 27 Grid 36 n/c
26 n/c 35 +HV

Lcl Ctl Adapter (SCR-274N, ARC-5)
J-32 (6962) To Rec Adapt. Cavity
1 Gain Ctl 4 n/c 7 +LV to Rec
2 Gnd 5 CW Shut-off 8 n/c
3 n/c 6 +LV Source

Audio Adapter (ARC-5)
J-27 (6036) To Rec Adapt Cavity
1 Gain Ctl 4 Navig. Audio 7 +LV (Jmpr to 6)
2 Gnd 5 CW Shut-off 8 n/c
3 n/c 6 +LV (Jmpr to 7)

J-28 (9336) to External Eq't
1 Audio 2 Gnd 3 Relay Ctl

Control Boxes (SCR-274N, ATA/ARA)

Transmitter Ctl Box
J-55 (7027) To Modulator
1 Sel Trans 1 7 Gnd 13 Modulator Cath.
2 " " 2 8 Mic 14 1000-cycle Off
3 " " 3 9 Key 15 +LV to Eq't
4 " " 4 10 Voice Sidetone 16 Voltage Regulator
5 Meter + 11 Tone Sidetone 17 Sidetone Inject
6 Meter - 12 Dyn. Relay 18 +LV Source

J-56 (2674) To External Meter
+ Meter + (blank) Meter -

Receiver Ctl Boxes (Single or Multi.)
J-25,-26,-27 (6418) To Rec Rack
1 +LV Source 4 Gnd 7 CW Shut-off
2 Rec Audio 5 B-Tel 8 A-Tel
3 Gain Ctl 6 +LV to Rec

Control Boxes (ARC-5)

Single Rec, Tunable (C-26)J-4 (6418) To Rec Rack
1 +LV Source 4 Gnd 7 CW Shut-off
2 Rec Audio 5 B-Tel 8 A-Tel
3 Gain Ctl 6 +LV To Rec

Single Rec, Lock-tuned (-27)
J-5 (9835) To Rec Rack
1 Gain Ctl 2 Gnd

HF Trans Ctl (C-29)
J-77 (5571) To Modulator
1 Sel Trans 1 7 Gnd 13 Modulator Cath.
2 " " 2 8 n/c 14 lO00-cycle Off
3 " " 3 9 Key 15 +LV to Eq't
4 " " 4 10 Voice Sidetone 16 Voltage Reg.
5 n/c 11 Tone Sidetone 17 Sidetone Inject
6 Sel Common 12 Dyn. Relay 18 +LV Source

HF Trans & VHF Chan Sel (C-30,-30A)
J-402,-1700 (5571) To Modulator
- Pinout same as J-77 on C-29 above)

J-401,-1701 (7025) To VHF Eq't
1 Trans Chan A 5 Gnd 9 Rec Chan C
2 " " B 6 Key 10 " " D
3 " " C 7 Rec Chan A 11 Voltage Reg
4 " " D 8 " " B 12 n/c

Main Ctl Box (C-38)
J-1001 (7027) To Eq't or Junct. Box J-17
1 Sens(VHF) 7 Gnd 13 Sens(ARB)
2 Sens(HF) 8 Key(MHF) 14 Pitch(ARR-2)
3 Mic Inp(MHF) 9 Key(VHF) 15 Key(Pilot)
4 Mic Inp(VHF) 10 CW S-O(ARR-2) 16 Key(ICS)
5 Mic Inp(ICS) 11 Audio(Pilot) 17 Sens(ARR-2)
6 Mic(Pilot) 12 Audio Buss 18 Audio(VHF)

Auxiliary Ctl Box (C-39,-48) *14
J-1101,-1102 (7025) To Eq't or Junct. Box J-17
1 Audio(ICS) 5 Gnd 9 Key(VHF)
2 Audio Buss 6 Mic Inp(HF) 10 n/c
3 Key(ICS) 7 Mic Inp(VHF) 11 Key(HF)
4 n/c 8 Mic Inp(ICS) 12 +LV

J-1103 (9336) To External Key
1 n/c 2 Gnd 3 Key

VHF Rec Ctl Box (C-42)
J-460 (6418) To Rec Rack
1 +LV Source 4 Gnd 7 AVC Ctl
2 Rec Audio 5 B-Tel 8 A-Tel
3 MVC (Gain Ctl) 6 +LV To Rec

J-463 (2674) To Rec Rack (J-6 or J-7)
+,(blank) Rec Audio (shell) Gnd

HF & VHF Rec Ctl (C-43)
J-410,-411 (6418) To Rec Rack, HF Rec Positions
1 +LV Source 4 Gnd 7 CW Shut-off
2 Rec Audio 5 B-Tel 8 A-Tel
3 Gain Ctl 6 +LV to Rec

J-412 (6418) To Rec Rack, VHF Position
-Pinout as J-460 on C-42 above-

J-413 (2674) To Rec Rack (J-6 or J-7)
+,(blank) VHF Audio (shell) Grid

Single Rec, Tunable (C-125)
J-1900 (6418) To Rec Rack
1 +LV Source 4 Gnd 7 CW Shut-off
2 n/c 5 n/c 8 n/c
3 Gain Ctl 6 +LV to Rec

Single Rec, LF Tunable (C-744)
J-1900 (6418) To Rec Rack
1 n/c 4 Gnd 7 n/c
2 Panel Lights 5 n/c 8 n/c
3 Gain Ctl 6 n/c

Control Boxes (Type 12)

Single Rec, LF (C-16)
J-701 (11905) to Rec
A n/c C Gnd E Sens
B Ant/Loop Sw D +LV to Rec F +LV Source

Single Rec, VHF (C-17)
J-801 (11905) To Rec
A n/c C Gnd E Sens
B Audio Hi-Lo D +LV to Rec F +LV Source

3 Rec, 2 Trans, Loop (C-24)
J-lO01 (12096) To Eq't or Junct. Box
A Sel Chan 1 H Sel Trans 2 O Sens (Range)
B " " 2 I Chan Sel Common P Ant/Loop (Range)
C " " 3 J +LV (VHF) Q Sens (Bcst)
D " " 4 K +LV (Range) R Ant/Loop (Bcst)
E " " 5 L +LV (Bcst) S n/c
F Mic Key M Sens (VHF)
G Sel Trans 1 N Audio Hi-Lo (VHF)

J-1002 (12093) To Primary Power Source
A +LV Source B Gnd
C " " D "

3 Trans (C-25)
J-1101 (12096) To Eq't or Junct. Box
A Sel Chan 1 H Grid O Mic Audio
B " " 2 I Trans Sidetone P Mic Key
C " " 3 J Mic Audio (Tr 2) Q Gnd
D " " 4 K Key (Trans 2) R Tel
E " " 5 L Rec Audio S n/c
F Mic Audio (Tr 1) M Mic Audio (Ext Tr)
G Key (Trans 1) N Key (Extern Trans)

2 Rec, 3 trans,(Loop)(C-36,-37.-38)
J-901,-1601,-2601 (12096) To Eq't or Junct Box
A Sel Chan 1 H Key (Tran 2) O Mic (tran 1 & 2)
B " " 2 I Key (Extrn Tran) P Mic (Extrn Tran)
C " " 3 J Rng/VHF Audio Q n/c
D " " 4 K Tel (Junct. Box) R
E " " 5 L Sidetone (Trl&2) S
F Relay (Junct Box) M Key (Junct Box) *15
G Key (Tran 1) N Mic (Junct Box)

J-902,-1602,-2602 (12097) To Eq't or Junct Box
A Sens (Range) D Sens (VHF) G +LV Source
B Ant/Loop Sw (Rng) E Hi-Lo Audio (VHF) H Gnd
C +LV (Range) F +LV (VHF)

2 Rec, 2 Trans, Loop (C-39)
J-1701 (12096) To Eq't or Junct Box
A Sel Chan 1 H Sel Tran 2 O Sens (range)
B " " 2 I n/c P Ant/Loop (Range)
C " " 3 J +LV (VHF) Q n/c
O " " 4 K +LV (Range) R n/c
E " " 5 L n/c S n/c
F Mic Key M Sens (VHF)
G Sel Trans 1 N Audio Hi-Lo (VHF)

J-1702 (12093) To Primary Power Source
A +LV Source C Gnd
B +LV Source D Gnd

3 Rec, 3 Trans (C-40)
J-1801 (12096) To Eq't or Junct Box
A ARC-5 VHF Ch A H Relay (Junct Bx) O Tel Out (Extrn)
B " " " B I Tel Set P +LV to ARC-5 Trans
C " " " C J Sidetone Q +LV Source
D " " " D K Rec Tel Out R " "
E Sel Trans (VHF) L Key (Extrn Tran) S Gnd
F " " (HF) M Key (ARC-5)
G " " Common N Key (Mic)

J-1802 (12097) To Eq't Or Junct Box
A +LV (ARC-5 Rec) D Sens (R-11) G Sens(R-19)
B Sens (ARC-5 Rec) E Ant/Loop (R-11) H Audio Hi-Lo (R-19)
C +LV (R-11) F +LV (R-19)

1 Rec, Loop (C-48)
J-1802 (12097) To Eq't *16
A Panel Lights D +LV to Rec G n/c
B Ant/Loop Sw E Sens H n/c
C Gnd F +LV Source

1 Rec, 4 Trans (C-56)
J-1801 (12096) To Eq't or Junct. Box
A Sel Chan 1 H Mic (Trans 2) O +LV to Eq't
B " " 2 I Mic (Trans 3) P Sens (Top of Pot)
C " " 3 J Key In Q Mic (Trans 4)
D " " 4 K Key (Trans 1) R Sens (Pot Tap)
E " " 5 L Key (Trans 2) S Whistle Stop
F Mic In M Key (Trans 3) *17
G Mic (Trans 1) N Chan Sel (Trans 4)

J-1701 (12093) To Eq't or Junction Box
A +LV Source C Gnd
B Sel Trans 4 D Panel Lights

Junction & Jack Boxes (ARC-5)

Jack Box, Mic/Tel (J-16,-22) *14
J-1201 (9336) To Mic
1 Mic 2 Key 3 Gnd

J-1202 (7026) To Junct Box J-17
1 Mic 4 Gnd 7 Key
2 Audio 5 n/c 8 +LV In *18
3 n/c 6 n/c

System Junction Box (J-17)
J-1301 (6418) To APC-5 VHF Rec
1 n/c 4 Gnd 7 AVC Ctl
2 Rec Audio 5 n/c 8 n/c
3 Sens 6 +LV to Rec

J-1302 (6418) To ARB MHF/HF Rec
1 n/c 4 Gnd 7 CW Shut-off
2 Rec Audio 5 CW Gain 8 AVC
3 Sens 6 +LV to Rec

J-1303(6418) To ARC-5 HF Rec
1 n/c 4 Gnd 7 CW Shut-off
2 Rec Audio 5 B-Tel 8 n/c
3 Sens 6 +LV to Rec

J-1304(6418) To R-4/ARR-2 Rec
1 n/c 4 Gnd 7 CW Shut-off
2 Sens 5 Rec Audio 8 n/c
3 Pitch 6 +LV to Rec

J-1305 (7024) to Modulator
1 +LV Source Out 2 Gnd 3 +LV Source Out

J-1306 (7026) To HF Trans
a) ARC-5 Trans
1 Mic 4 Gnd 7 Key
2 A-Tel 5 Sidetone 1 8 +LV
3 B-Tel 6 Sidetone 2
b) ART-13 Trans
1 n/c 4 Gnd 7 n/c
2 n/c 5 Mic 8 n/c
3 Key 6 Sidetone

J-1307 (6418) Test or as spec.
1 n/c 4 Gnd 7 n/c
2 Audio 5 n/c 8 n/c
3 n/c 6 +LV Out

J-1308 (6418) To ARC-1 or ARC-4
1 +LV 4 Gnd 7 n/c
2 Audio 5 Mic 8 Key
3 Gnd 6 +LV

J-1309 (7024) To Primary Power Source
1 +LV Source In 2 Gnd 3 +LV Source In

J-1310 (7026) To Mic/Tel Jack Box (J-16,-22)
1 Mic 4 Gnd 7 Key
2 Audio 5 n/c 8 +LV
3 n/c 6 n/c

System Junction Box (J-17)
J-1301 (6418) To ARC-5 VHF Rec
1 n/c 4 Gnd 7 AVC Ctl
2 Rec Audio 5 n/c 8 n/c
3 Sens 6 +LV to Rec

J-1302 (6418) To ARB MHF/HF Rec
1 n/c 4 Gnd 7 CW Shut-off
2 Rec Audio 5 CW Gain 8 AVC
3 Sens 6 +LV to Rec

J-1303(6418) To ARC-5 HF Rec
1 n/c 4 Gnd 7 CW Shut-off
2 Rec Audio 5 B-Tel 8 n/c
3 Sens 6 +LV to Rec

J-1304(6418) To R-4/ARR-2 Rec
1 n/c 4 Gnd 7 CW Shut-off
2 Sens 5 Rec Audio 8 n/c
3 Pitch 6 +LV to Rec

J-1305 (7024) to Modulator
1 +LV Source Out 2 Gnd 3 +LV Source Out

J-1306 (7026) To HF Trans
a) ARC-5 Trans
1 Mic 4 Gnd 7 Key
2 A-Tel 5 Sidetone 1 8 +LV
3 B-Tel 6 Sidetone 2
b) ART-13 Trans
1 n/c 4 Gnd 7 n/c
2 n/c 5 Mic 8 n/c
3 Key 6 Sidetone

J-1307 (6418) Test or as spec.
1 n/c 4 Gnd 7 n/c
2 Audio 5 n/c 8 n/c
3 n/c 6 +LV Out

J-1308 (6418) To ARC-1 or ARC-4
1 +LV 4 Gnd 7 n/c
2 Audio 5 Mic 8 Key
3 Gnd 6 +LV

J-1309 (7024) To Primary Power Source
1 +LV Source In 2 Gnd 3 +LV Source In

J-1310 (7026) To Mic/Tel Jack Box (J-16,-22)
1 Mic 4 Gnd 7 Key
2 Audio 5 n/c 8 +LV
3 n/c 6 n/c

System Junction Box (J-17) con't
J-1311 (7025) To Auxiliary Ctl Box (C-39,-48)
1 Audio (ICS) 5 Gnd 9 Key
2 Audio Buss 6 Mic (MHF) 10 n/c
3 Key (ICS) 7 Mic (VHF) 11 Key (MHF)
4 n/c 8 Mic (ICS) 12 +LV

J-1312 (7027) To Main Ctl Box (C-38)
1 Sens (VHF) 7 Gnd 13 Sens (ARB)
2 Sens (MHF) 8 Key (MHF) 14 Pitch (ARR-2)
3 Mic (MHF) 9 Key (VHF) 15 Key (Pilot)
4 Mic (VHF) 10 CW S-O (ARR-2) 16 Key (ICS)
5 Mic (ICS) 11 Audio (Pilot) 17 Yens (ARR-2)
6 Mic (Pilot) 12 Audio Buss 18 Audio (VHF)

J-1313 (6418) To RL-7,-9 or Cat ICS
a) RL-7,-9
1 n/c 4 Gnd 7 n/c
2 Audio 5 Mic In 8 n/c
3 n/c 6 +LV
b) Cat ICS
1 n/c 4 Gnd 7 Audio
2 n/c 5 Mic In 8 n/c
3 n/c 6 +LV

Ctl Split, VHF Chan. (J-28)
J-1401 (7025) To Ctl Box C-30,-30A
1 Trans Chan A 5 Gnd 9 Rec Chart C
2 " " B 6 Key 10 " " D
3 " " C 7 Rec Chan A 11 Voltage Reg.
4 " " D 8 " " B 12 n/c

J-1402 (7026) To VHF Trans (T-23)
1 Trans Chan A 4 Gnd 7 Voltage Reg.
2 " " B 5 Trans Chan D 8 n/c
3 " " C 6 Key

J-1403 (5577) To VHF Rec (R-28)
1 Rec Chan A 3 Gnd 5 Rec Chan D
2 " " B 4 Rec. Chan C 6 n/c

Ctl Split, Multi Trans Rack (J-34)
J-1501,-1502,-1503 (9417) To Modulator & Trans Racks '19
1 +LV 5 Sel Trans 3 9 +HV
2 Sel Trans 1 6 " " 4 10 Osc. B+
3 " " 2 7 Key 11 Test Relay
4 Gnd 8 P.A. B+ 12 P.A. Vscr

Racks

Receiver Racks, Command Set (All Series)
J-6,-7,-601,-602 (5577) To Modulator *6
1 Sidetone 1 3 Gnd 5 Key
2 A-Tel 4 B-Tel 6 +LV

J-18,-19,-20,-31,-603 (5842) To Rec
1 Gnd 4 CW Shut-off *7 7 n/c
2 Rec Audio 5 n/c
3 Gain Ctl 6 +LV To Rec

J-21,-22,-23,-32,-605 (6418) To Ctl Box
1 +LV Source 4 Grid 7 CW Shut-off *7
2 Rec Audio 5 B-Tel 8 A-Tel
3 Gain Ctl 6 +LV to Rec

J-24,-604 (6485) To Primary Power Source
1 +LV Source In 2 Gnd

Trans Racks (SCR-274N,ATA)
J-59 (7025) To Modulator
1 Meter + 5 Gnd 9 Sel Trans 1
2 Meter - 6 Sel Trans 4 10 P.A. B+
3 Key 7 " " 3 11 Osc. B+
4 +LV 8 " " 2 12 P.A. Vscr

J-60 (7023) To Antenna Relay
1 Key 3 Gnd 5 Meter -
2 Meter + 4 +LV

J-62,-63,-67,-68 (5842) to Trans
1 Gnd 4 P.A. Vscr 7 P.A. B+
2 n/c 5 Select (Key)
30sc. B+ 6 +LV

Trans Racks (ARC-5)
J-56 (2674) To Extern Ant Meter
+ Meter + (blank) Meter -

J-60 (7023) To Antenna Relay
1 Key 3 Gnd 5 Meter -
2 Meter + 4 +LV

J-67,-68,-80,-82 (9296) To Trans
1 +HV 4 Gnd 7 P.A. B+
2 Osc. B+ 5 +LV
3 Select (Key) 6 P.A. Vscr

Trans Racks (ARC-5) con't
J-71 (9417) To Modulator
1 +LV 5 Sel Trans 3 9 +HV
2 Sel Trans 1 6 " " 4 10 Osc. B+
3 " " 2 7 Key 11 Test Relay
4 Gnd 8 P.A. B+ 12 P.A. Vscr

Related Equipment (ARC-5)

R-4/ARR-2 Homing Rec
J-402 (5488) To Rack '21
1 Gnd 4 n/c 7 n/c
2 Rec Audio 5 n/c
3 n/c 6 +LV In

J-104 (6418) To Control Box
1 +LV Source 4 Gnd 7 CW Shut-off
2 Sens 5 Rec Audio 8 Tel (To Rack)
3 Pitch 6 +LV TO Rec

C-2/ARR-2 Control Box for R-4/ARR-2
1 +LV Source 4 Gnd 7 CW Shut-off
2 Sens 5 Rec Audio 8 Tel (to Rack)
3 Pitch 6 +LV to Rec

Related Equipment (Type 12)

TV-10 (CV-431/AR) Transvertor
J4202 ( ) To Chan Sel Ctl *23
A Sel Chan 1 E Sel Chan 5 I UHF/VHF Sel
B " " 2 F " " 6 J Whistle-thru
C " " 3 G " " 7 K Grid
D " " 4 H " " 8 L Hi-Lo Freq Range

J-4203 ( ) To Set Ctl *24
A +LV Source E Key I UHF/VHF Sel
B +HV In F VHF Ant Disable J n/c
C +HV to VHF G Sidetone K Gnd
D Mic H Whsl-thru (VHF) L n/c

R-20 Marker Beacon Rec
J-2702 (11905) To Ctl
A +HV to Rec C Gnd E Relay Out
B Rec Audio D +LV In F n/c

R-22 Rec, Broadcast
J-4803 ( ) To Ctl
A +LV to Rec E Sens I n/c
B +HV to Rec F Ant/Loop Sw J n/c
C +HV to Trans G Rec Audio K Grid
O Gnd H n/c L n/c

R-13 (R-445/ARN-30) Type 15 VOR/ILS Rec
J-lO3 ( ) To Equipment Rack *25
1 Gnd 4 Tuning Meter 7 +HV Out
2 Rec Audio 5 Navig Audio
3 Gain Ctl 6 +LV Source In

J-lO5 (11905) To Trans *2,26
A +HV To Trans C Grid E +HV to Rec
B Rec Audio D +LV to Trans F n/c

R-34 (R-1021/APN-3OD) Type 15 VOR/ILS Rec
J-2 (12357) To Control
A n/c H MHz Tuning Ctl O 0.1 MHz Tun'g Ctl
B n/c I " " " P " " " "
C n/c J " " " Q " " " "
D n/c K " " " R " " " "
E Local Squelch L " " " S Gnd
F Squelch Circuit H Localizer Key
G n/c N 0.1 MHz Tun'g Ctl

J-3 (11905) To Trans *2
A +HV to Trans C Gnd E +HV to Rec
B Rec Audio D +LV to Trans F Rem. Squelch Ctl

J-4 ( ) To Rack *25
1 Gnd 4 Tuning Meter 7 +HV Out
2 Rec Audio 5 Navig Audio
3 Gain Ctl 6 +LV Source

Other A.R.C. Equipment

RT-524() VHF Transceiver *27
J-3-( ) Power and Audio *22,28
A Gnd H Speaker Out P +LV IN (Unsw'd)
B n/c J Aux Audio 2 In R RT-524 Audio In
C Phone Out K +LV Out (Sw'd) S Amp +LV In
D Aux Audio 1 In L Spkr Sidetone T Aux Audio 4 In
E Panel Lights M Mic Key U +LV In To Switch
F n/c N Aux Audio 3 In V Mic Input

R-836/ARN-59 ADF Rec
J-101 (12426) To Loop Ant
A Loop Input 1 B Loop Input 2 C Gnd

J-103 (12357) Power & Ctl
A +LV In H Band III Sel O AF Plate Out
B +HV2 In (125v) I 13V, 100~, 0 deg. in P n/c
C +HV1 In (llOv) J Tel Q Loop Position
D Modulator Ctl K Sens R Loop Relay
E AF Grid In L BFO Ctl S Gnd
F Band I Sel M +/- Plate
G Band II Sel N -/+ Plate

C-2275/ARN-59 Ctl Box for P-836 J-201 (12357) To Equipment
A n/c H Band I Sol O Gain Ctl (AF Pl.)
B Phase 2 Ctl I BFO Ctl P Sens
C Band Sel Gnd J Panel Lights Q Power Ctl
D n/c K Loop Position R Modulator Ctl
E Gain (AF Grid) L 13v,100~,0/180 deg. S Gnd
F Band III Sel M 13v,100~,180/0 deg. *29
G Band II Sel N Loop Relay Ctl

Notes
1 Only used on .19-.55 & .52-1.5 MHz Rec's
2 If no transmitter is used, jumper pins A & E with wired plug
ABC# 11934
3 T-15,-16,-17
4 Only Rec Audio plus Trans Sidetone
5 Pins G & H not used in any installation drawings found
6 J-6,-? (J-601,-602) are identical & either may go to the
modulator. The other is for connecting multiple rec. racks
together as one system.
7 AVC Ctl when VHF rec (R-28) is installed.
8 Not on R-28
9 On M-28 Only
10 On T-23 Only
11 Both the same. Allows 2 LF/MF transmitters to connect to 1
antenna tuner
12 On early control boxes only
13 Pins 1 & 6 jumpered in control box
14 Also has JK-48 on a cord and mic & phone jacks
15 Tran 2 only has 4 channels. Position 5 for tran 2 goes to
pin F rather than pin E.
16 Proper ident for connector not available yet.
17 Position 16 selects Tran 3 with no crystal for ICS use.
18 On J-22,-22() only
19 All connectors the same and are interchangeable.
20 No Test Set-ups are included.
21 MX-2/ARR-2 Wired Plug is required in Ctl Box recept on rack.
This jumpers pins 1 & 6, and 2 & 8 together to allow the
receiver to work from the control box attached to it.
22 Not an A.R.C.-type connector
23 Key notch over pin B
24 Key notch over pin I
25 Connector similar to ARC# 5488
26 Not on R-13
27 'A' suffix freq range is 118.00-135.95 MHz.
'M' suffix freq range is 136.00-149.95 MHz.
Pinout shown is from 'A' equipment and is assumed to be
the same as 'M' equipment.
28 Aux and PT-524 Audio inputs are to internal mixer/amp,
which may be used independently of the rest of the radio.
29 Pins L & M are switched for different antenna mounts.
The first angle is for belly-mounted antennas and the second
is for top-mounted antennas.

CONNECTOR LISTS

All Command series and Type 12 receptacles are shown on the following pages
in numeric order. Some extra A.R.C. connectors are shown as well where I have
information on them. The receptacles are shown as viewed from the outside. Pin 1
or A is indicated on the drawings, and the pin identification proceeds from
there anti-clockwise. It should be noted that in many if not all cases, the pins
are marked on the wired side of the connectors.

Some crossing between Command and Type 12 connectors is possible as shown in
the notes. (Notes are indicated as in the previous section.) For the most part,
Command set connectors are unkeyed, while the later Type 12, etc ones do have
keying ridges. The keying can be defeated (Files are handy for this.) to allow
the later type plugs to be used in the Command set receptacles, as well as in
ones with the same pin arrangement but different keying.

There are other A.R.C. connectors however these aren't shown due to lack of
information on them.

Recept No Front Mating Plugs
Ident Pins View Cable Open Used On
Wire

2674 2 3146 C-42,-43, ARC-5 Trans Racks
PL-157 Early BC-451's

5571 18 6962 9585 C-29,-30, ARC-5 Modulator

5577 6 6784 9123 J-28, R-28, All Rec Racks,
*1 PL-151 PL-151A All Modulators

5842 7 5488 (on rear All Rec Racks, SCR-274N &
*2 of Equipment) ATA Trans Racks

C-2,-26,-42,-43,-125,-744,
6418 8 6577 9125 SCR-274N & ARA Rec Ctl Boxes,
*3 PL-152 PL-152A R-4, T-23

6485 2 6578 9127 All Rec racks
PL-147 PL-147A

7023 5 6967 9124 All Trans Racks & Ant Relays
PL-156 PL-156A

7024 3 6965 9126 J-17, All Modulators
PL-148 PL-148A

C-30,-39,-48, J-17,-28,
7025 12 6964 9122 SCR-274N & ATA Modulators
PL-154 PL-154A & Trans Racks

7026 8 6966 9121 J-17,-28, T-23, MD-7

7027 18 6963 9121 C-38, J-17, SCR-274N & ATA
PL-153 PL-153A Modulators & Trans Ctl Boxes

9296 7 9302 (On rear ARC-5 Trans Racks
of ARC-5 Trans)

9336 3 -- 9488 -- C-39,-48, J-16,-22, ~IX-19

9417 12 9377 9589 J-34, MD-7,
ARC-5 Trans Racks

9835 2 -- 9818 -- C-27

9849 3 -- 9848 -- TN-60 T-15,-16,-17

11905 6 12151 14051 C-16,-17, R-13,-20,-34,
*1 Type 12 Rec & Trans

12093 4 12372 14052 C-24,-39,-56, Type 12 Tran8
12375

12095 7 (On rear ARN-30 (Type 15) Equipment
*2 Of Rack-mt Eq't) Racks

12096 19 12139 14320 C-24,-25,-36,-37,-38,-39,
*4 C-40,-56

C-36,-37,-37,-40,-48,
12097 8 12098 14050 C-3436/ARN-30D, Type 12 Trans,
*3 Type 15 Eq't Rack

12348 8 Type 15 Eq't Rack
*3

12355 8 C-3436/ARN-30D
*3

12357 19 C-2275 & R-836/ARN-59
*4 C-3436 & R-1021/ARN-30D
Type 15 R-34

12426 3 R-836/ARN-59

12427 2 14321 Type 12 Rec's, Type 15 Racks

12 TV-10 (CV-431/AR)

12 TV-10 (CV-431/AR)

12 R-22

NOTES

1 Plugs for receptacles 5577 and 11905 may be used inter-
changeably if the keying is defeated on the newer plugs.

2 A.R.C. Type 15 receivers may be used in Command set receiver
racks and vice-versa if wiring changes are made to accommodate
the different pinouts.

3 Plugs for receptacles 6418, 12097, 12348, and 12355 may be
used interchangeably if the keying is defeated on the
newer plugs.

4 Plugs for receptacles 12096 and 12357 may be used inter-
changeably if the keying is defeated. Some caution should
be exercised since without the keys there are several ways
to insert the plugs into the receptacles.

SCR-274N to A.R.C. Plug Cross Reference

SCR-274N A.R.C.
Ident Ident
PL-147 6578
PL-147A 9127
PL-148 6965
PL-148A 9126
PL-151 6784
PL-151A 9123
PL-152 6577
PL-152A 9125
PL-153 6963
PL-153A 9121
PL-154 6964
PL-154A 9122
PL-156 6967
PL-156A 9124
PL-157 3146

NUMERIC ORDER LISTS

The following lists are divided into two groups. The first is a set of "in
type" lists for the various series from the first sections of this booklet. The
second is a list of all the units previously mentioned for which A.R.C. part
numbers were found, and is in numeric order by that number.

Note that some items not in the equipment lists are listed here. these are
'uncommon units (such as the VHF SCR-274N units) or detail pieces (like
connector caps.) These lists are therefore more complete than the previous ones
and are useful as 'check lists' for these items.

An asterisk used as a suffix to a unit's identifier indicates that there are
or may be trailing letters and that all versions are being referred to. For
example, C-30' refers to both the C-30 and the C-30A.

SCR-274N

BC-442 Antenna Relay FT-231 Mount, 1 Rec
BC-450 Ctl Box, 3 Rec FT-232 Mount, 1 Trans
BC-451 Ctl Box, Trans FT-233 Rack, 1 Rec
BC-453 Rec, .19-.55 MHz FT-234 Rack, 1 Trans
BC-454 Rec, 3.0-6.0 MHz FT-235 Mount, 1 Rec Ctl Box
BC-455 Rec, 6.0-9.1 MHz FT-240 Mount, 2 Rec Ctl Box
BC-456 Modulator FT-260 Adapter, Local Ctl
BC-457 Trans, 4.0-5.3 MHz FT-262 Mount, 3 Trans
BC-458 Trans, 5.3-7.0 MHz FT-264 Rack, 4 Rec
BC-459 Trans, 7.0-9.1 MHz FT-276 Rack, 3 Trans
BC-473 Ctl Box, 1 Rec FT-277 Rack, 2 Rec
BC-496 Ctl Box, 2 Rec FT-278 Mount, 4 Rec
BC-696 Trans, 3.0-4.0 MHz FT-279 Mount, 2 Rec
BC-938 Ctl Box, HF & VHF Trans FT-310 Adapter, Power
BC-942 Rec, 100-156 MHz FT-331 Rack, 4 Trans
BC-9~6 Rec, .52-1.5 MHz FT-332 Mount, 4 Trans
BC-950 Trans, 100-156 MHz I-84A Meter Unit, Rec Test
DM-32 Dynamotor, Rec I-85A Meter Unit, Trans Test
DM-33 Dynamotor, Trans MC-211 Adapter, Rt Angle Drive
FT-220 Rack, 3 Rec MC-212 Dial, 6.0-9.1 MHz
FT-221 Mount, 3 Rec MC-213 Dial, 3.0-6.0 MHz
FT-222 Mount, 3 Rec Ctl Box MC-214 Dial, .19-.55 MHz
FT-225 Mount, Modulator MC-215 Kit, Tuning Shaft
FT-226 Rack, 2 Trans MC-415 Dial, .52-1.5 MHz
FT-227 Mount, 2 Trans PL-192 Wired Plug
FT-228 Mount, Trans Ctl Box RC-54A Test Set-up, Rec
FT-229 Mount, Antenna Relay RC-55A Test Set-up, Trans
FT-230 Adapter, Remote Ctl

NAVY

21531 Dynamotor, Rec 50084 Mount, Modulator
21626 Dynamotor, Trans 50141 Modulator, ARC-5
23155 Ctl Box, 2 Rec 52208 Trans, ATA, 3.0-4.0 MHz
23243 Ctl Box, Trans 52209 Trans, ATA, 4.0-5.3 MHz
23251 Ctl Box, 3 Rec 52210 Trans, ATA, 5.3-7.0 MHz
23261 Ctl Box, 1 Rec 52211 Trans, ATA, 7.0-9.1 MHz
29125 Antenna Relay 52212 Rack, 2 Trans
29126 Mount, Antenna Relay 52213 Mount, 2 Trans
46085 Mount, 2 Rec 52232 Trans ATA, 2.1-3.0 MHz
46104 Rec, 1.5-3.0 MHz 52302 Trans ARC-5, .50-.80 MHz
46105 Rec, 3.0-6.0 MHz 52303 Trans ARC-5, .80-1.3 MHz
46106 Rec, 6.0-9.1 MHz 52304 Trans ARC-5, 1.3-2.1 MHz
46110 Rack, 2 Rec 52305 Trans ARC-5, 2.1-3.0 MHz
46129 Rec, .19-.55 MHz 52306 Trans ARC-5, 3.0-4.0 MHz
46145 Rec, .52-1.5 MHz 52307 Trans ARC-5. 4.0-5.3 MHz
46149 Rack, 3 Rec 52308 Trans ARC-5, 5.3-7.0 MHz
46150 Mount, 3 Rec 52309 Trans ARC-5, 7.0-9.1 MHz
49107 Adapter, Remote Ctl 62036 Adapter, Power
50083 Modulator, ATA

ARC-5

C-24 Adapter, Local Ctl MT-69 Rack, 1 Trans
C-25 Ctl, Rem Ant/Loop Sw MT-70 Mount, 2 Trans
C-26 Ctl Box 1 Rec, Tunable MT-71 Rack, 2 Trans
C-27 Ctl Box 1 Rec, Lock-tuned MT-72 Mount, 3 Trans
C-29 Ctl Box HF Trans MT-73 Rack, 3 Trans
C-30* Ctl Box HF Trans & VHF Chan MT-74 Mount, 4 Trans
C-38 Ctl Box Main MT-75 Rack, 4 Trans
C-39 Ctl Box Auxiliary MT-76 Mount, Modulator
C-42 Ctl Box 1 Rec, VHF MT-77 Mount, Antenna Relay
C-43 Ctl Box 3 Rec, HF & VHF MT-78 Mount, Ctl & Jack Box
C-48 Ctl Box Auxiliary MT-80 Mount, Ctl & Junct Box
C-125 Ctl Box 1 Rec, Tunable MT-84 Mount, Junct Box
C-131 Ctl Head 6 chan, HF Rec MT-98 Mount, Ctl Box
C-744 Ctl Box, 1 Rec, Tunable MT-159 Mount, Antenna Tuner
DY-1 Dynamotor, Rec, 12v MT-411 Rack, 1 Rec, 12v
DY-2* Dynamotor, Rec MX-19 Adapter, Audio
DY-8 Dynamotor, Trans MX-20 Adapter, Power
ID-25 Dial, .19-.55 MHz MX-21 Adapter, Remote Ctl
ID-26 Dial, .52-1.5 MHz MX-22 Adapter, Rt Angle Drive
ID-2? Dial, 1.5-3.0 MHz 0-4A 0sc, Lock-tuned Rec Tune
ID-28 Dial, 3.0-6.0 MHz R-23' Rec, .19-.55 MHz
ID-29 Dial, 6.0-9.1 MHz R-24 Rec, .52-1.5 MHz
J-16 Jack Box, Mic/Tel R-25 Rec, 1.5-3.0 MHz
J-17* Junction Box, System R-26 Rec, 3.0-6.0 MHz
J-22* Jack Box, Mic/Tel R-27 Rec. 6.0-9.1 MHz
J-28 Junct Box, VHF Chan Split R-28 Rec, 100-156 MHz
J-33 Wired Plug R-148 Rec, .19-.55 MHz
J-34 Junct Box, Trans Ctl RE-2 Antenna Relay
MD-7 Modulator T-15 Trans, .50-.80 MHz
MT-4 Mount, Ctl Box T-16 Trans, .80-1.3 MHz
MT-5 Mount, 1 Rec T-17 Trans, 1.3-2.1 MHz
MT-7A Rack, 1 Rec T-18 Trans, 2.1-3.0 MHz
MT-62 Mount, 2 Rec T-19 Trans, 3.0-4.0 MHz
MT-63 Rack, 2 Rec T-20 Trans, 4.0-5.3 MHz
MT-64 Mount, 3 Rec T-21 Trans, 5.3-7.0 MHz
MT-65 Rack, 3 Rec T-22 Trans, 7.0-9.1 MHz
MT-66 Mount, 4 Rec T-23 Trans, 100-156 MHz
MT-67 Rack, 4 Rec TN-6 Antenna Tuner
MT-68 Mount, 1 Trans

A.R.C. Equipment

A-12 Antenna, VHF J-12 Junction Box, 32 pos, 12v
B-13 Converter, VOR/ILS J-13 Junction Box, 32 pos, 24v
C-16 Ctl Box R-ll Rec J-15 Junction Box, 56 pos, 24v
C-17 Ctl Box R-15 Rec L-10 Antenna, Loop
C-18 Ctl Box Loop Heading M-11 Mount, 1 Rec
C-24 Ctl Box 3 Rec.2 Trans, Loop M-12 Mount, 1 Trans
C-25 Ctl Box 3 Trans M-13 Mount, Ctl Box
C-26 Ctl Box R-10 Rec M-18 Mount, Ctl Box
C-36 Ctl Box 2 Rec,3 Trans, Loop M-19 Mount, Ctl Box
C-37 Ctl Box 2 Rec, 3 Trans P-10 Power Supply, Trans Test
C-38 Ctl Box 2 Rec, 3 Trans P-11 Power Supply
C-39 Ctl Box 2 Rec,2 Trans, Loop R-10* Rec, .52-1.5 MHz
C-40 Ctl Box 3 Rec, 3 Trans R-11* Rec, .19-.55 MHz
C-48 Ctl Box R-11 Rec, Loop R-13 Rec, 108-136 MHz, Type 15
C-56 Ctl Box R-19 Rec, 4 Trans R-15 Rec, 108-136 MHz
C-81 Ctl Box R-34 Rec R-19 Rec, 118-148 MHz
C-88 Ctl Box R-34 Rec R-20 Rec, 75 MHz, Fixed-tuned
D-10* Dynamotor R-22 Rec, .52-1.5 MHz
DV-10 Dynaverter Power Supply R-34 Rec, 108-126.9 MHz, Type 15
E-14 Rack, Type 15 Rec & Conv T-11* Trans, 118-132 MHz
H-19 Test Set, Rec & Trans T-13* Trans, 132-148 MHz
J-10 Jack Box, Mic/Tel

A.R.C. Part Numbers

1943 Cover, For Recept 2226 7023 Recept, 5-pin. 1-1/8"
2226 Recept, Power Adapter 7024 Recept, 3-pin, 1-l/8
2674 Recept, 2-pin, 7/8" 7025 Recept, 12-pin, 1-5/8"
3146 Plug, 2-pin, PL-157 7026 Recept, 8-pin, 1-1/8
5005 Receiver, -46104 7027 Recept, 18-pin, 1-5/8"
5006 Receiver, -46105 7043 Control Box. BC-473,-23261
5007 Receiver, -46106 7053 Mount, FT-235,MT-4
5009 Transmitter, -52208 7054 Mount, FT-222,MT-98
5010 Transmitter, -52209 7056 Mount, FT-229,-29126
5011 Transmitter, -52210 7057 Mount, MT-159
5012 Transmitter, -52211 7058 Mount, FT-225,-50084
5013 Modulator, -50083 7059 Mount, FT-231,MT-5
5014 Control Box, BC-450,-23251 7060 Mount, FT-221,-46150,MT-64
5017 Ant. Relay,BC-442,-29125,RE-2 7061 Mount, FT-232,MT-68
5018 Rack, FT-277,-46110,MT-63 7062 Mount, FT-227,-SZ213,MT-?O
5019 Rack, FT-264,MT-67 7063 Mount, FT-262,MT-72
5020 Rack, FT-226,-52212 7064 Mount, FT-332,MT-74
5168 Dynamotor, DM-33,-21626,DY-8 7065 Mount, MT-77
5319 Cover, 1-1/8" Recept 7067 Mount, MT-76
5488 Plug, 7-pin,On Rack-mt eq't 7083 Mount, FT-228,MT-80
5571Recept, 18-pin, 1-5/8" 7095 Control Box, BC-451,-23243
5577 Recept, 6-pin, 1-1/8" 7314 Control Box, C-29
5694 Mount, FT-278,-46085,MT-62 7369 Rec Test Panel, 1-84A
5842 Recept, 7-pin,For Rack-mt eq't 7491 Knob
5950 Receiver, -46145 7507 Rack, FT-234
7509 Rack, FT-233,MT-7A
6051 Dial, MC-214,ID-25 7535 Dial, ID-27
6052 Dial, MC-415,ID-26 7537 Rack, FT-220,-46149,MT-65
6053 Dial, MC-213,ID-28 7544 Trans Test Panel, 1-85A
6054 Dial, MC-212,ID-29 7591 Modulator, BC-456
6090 Rack, FT-331 7594 Receiver, BC-453
6151 Tuning Shaft Kit, MC-215 7595 Receiver, BC-454
6357 Rt-angle Adaptor,MC-211,MX-22 7596 Receiver, BC-455
6418 Recept, 8-pin, 1-1/8" 7632 Transmitter. BC-457
6433 Adapter, FT-230,-49107,MX-21 7633 Transmitter, BC-458
6434 Adapter, FT-260,C-24 7634 Transmitter, BC-459
6485 Recept, 2-pin, 1-1/8" 7638 Rack, FT-276
6546 Control Box, BC-496,-23155 7777 Dummy Antenna, A-61A
6577 Plug, 8-pin, Cable, PL-152 7839 Receiver, -46129
6578 Plug, 2-pin, Cable, PL-147 7916 Transmitter, -52232
6743 Knob, MC-236,MC-237 7918 Rec Test Set-up, RC-54A
6767 Wired Plug, PL-192,J-33 7919 Trans Test Set-up, RC-55A
6784 Plug, 6-pin, Cable, PL-151
6831 Mount, FT-240
6962 Plug, 18-pin, Cable
6963 Plug, 18-pin, Cable, PL-153
6964 Plug, 12-pin, Cable, PL-154
6965 Plug, 3-pin, Cable, PL-148
6966 Plug, 8-pin, Cable
6967 Plug, 5-pin, Cable, PL-156

A.R.C. Part Numbers. Con't

9074 Adapter, FT-310.-62036.MX-20 9821 Plug. 8-pin. Open-wire
9121Plug.18-pin,Open-wire,PL-153A 9835 Recept. 2-pin. 7/8". Key lt
9122 Plug,12-pin.0pen-wire,PL-154A 9848 Plug. 3-pin, Key left
9123 Plug,6-pin. Open-wire,PL-151A 9849 Recept, 3-pin. 7/8". Key lt
9124 Plug,5-pin. Open-wire,PL-156A 9850 Control Box, C-27
9125 Plug.8-pin,Open-wire.PL-152A 9867 Jack Box. J-22
9126 Plug.3-pin. Open-wire.PL-148A 9901 Control Box, C-39
9127 Plug.2-pin. Open-wire.PL-147A 9902 Control Box, C-48
9202 Rack, MT-411 9903 Junction Box. J-17*
9296 Recept, 7-pin,For ARC-5 Trans 9904 Mount, MT-84
9302 Plug, 7-pin, On ARC-5 Trans 9905 Jack Box, J-16
9306 Rack, MT-69 9907 Jack Box, J-22A,B
9307 Rack, MT-71 9910 Control Box, C-30A
9308 Transmitter, T-18 9911 Control Box, C-125
9309 Transmitter, T-19
9310 Transmitter, T-20 10007 Receiver, R-23A
9311 Transmitter, T-21 10008 Receiver. R-148
9312 Transmitter, T-22 10009 Dynamotor. DY-2B
9313 Modulator, MD-7 11905 Recept,6-pin,l-1/8",Key up
9315 Transmitter, T-15 11934 Wired Plug
9316 Transmitter, T-16 12093 Recept. 4-pin, 7/8",Key up
9317 Transmitter, T-17 12095 Recept, 7-pin,For Rack-mt, eqt
9336 Recept,3-pin,7/8",key-up 12096 Recept,19-pin,l-5/8".Key up
9369 Oscillator. 0-4A 12097 Recept,8-pin,l-1/8",Key up
9375 Cover, 7/8" Recept 12098 Plug.8-pin,Cable,Key up
9377 Plug, 12-pin, Cable 12125 Plug.6-pin,Cable,Key up
9417 Recept, 12-pin, 1-5/8" 12139 Plug.19-pin,Cable,Key up
9451 Mount, MT-78 12296 Wire Antenna Kit
9488 Plug, 3-pin, Key up 12348 Recept,8-pin.l-l~8",Key rt
9554 Knob/cap 12355 Recept,8-pin,l-1/8",Key lt
9556 Trans Test Panel 12357 Recept,19-pin,l-5/8",Key lt
9558 Trans Test Set-up 12372 Plug,4-pin.Cable,Key up
9562 Junction Box, J-34 12375 Plug,4-pin,Cable,Key up
9584 Plug, 12-pin, Open-wire 12426 Recept,3-pin,7/8",Key up
9585 Plug, 18-pin, Open-wire 12427 Recept,2-pin,7/8",Key up
9593 Rack, MT-73 14050 Plug,8-pin,Open-wire,Key up
9594 Rack, MT-75 14051 Plug,6-pin. Open-wire, Key up
9595 Adapter, MX-19 14052 Plug.4-pin. Open-wire, Key up
9601 Control Box. C-26 14320 Plug,19-pin,Open-wire. Key up
9602 Receiver. R-23 14321 Plug.2-pin,Open-wire.Key up
9603 Receiver, R-24 14480 Dynamotor, D-10A(12v)
9604 Receiver. R-25 14482 Dynamotor, D-10A(24v)
9605 Receiver, R-26 14588 Cover, 1-1/8" Recept
9606 Receiver. R-27 14589 Cover, 7/8" Recept
9607 Antenna Tuner, TN-6 15392 Capacity Plate for T-13
9609 Junction Box, J-28 15900 Capacity Plate for T-13A
9610 Control Box, C-38
9808 Cover, Ant/Loop Sw Ctl
9818 Plug, 2-pin, Key lt

QUICK & DIRTY CONNECTIONS

There has been in the past three decades, a virtual plethora of articles on
the conversion of the Command (and later, the Type 12 et al) radios. These have,
over that span, covered every reason- able (and I suppose an occasional
unreasonable) use that these units might have. However these sources are no
longer available which leaves the current user with a minor disadvantage, In
order to at least partially fill the information gap, following are a few simple
hook-ups (not really conversions in the strict sense of the term) which will get
the radios working with a minimum of fuss and bother. A couple of wiring
diagrams are shown at the end to aid where the descriptions are lacking in
clarity. The over-all result is essentially a starting point from which you may
launch your own ideas.

Except for the Command transmitters and the R-836/ARN-59, the units all will
run form a power supply good for 24v at 1.5 to 2 amps and around 250v at 80-100
ma. To use the transmitters and transverter, the low voltage should be rectified
and well filtered, although there's no reason this cant be done only where it's
, necessary.

Probably the best supply for these units is the one Fair Radio has. This is
not only a power supply, but also has a speaker, phone jack, gain control and
BFO switch (which can be used for other things as we'll see later.) The
cabinetry is nice and there is enough room inside for extra goodies should they
be desireable,

Another route is to get a dynamotor and remove everything from the base
except the plug and snap-slides. A very neat power supply can now be built on
the base so the whole shebang fits in the old dynamotor space. The Fair #818
transformer was designed to run the Command sets and is perfect for this.

Now that we've got power, let's see what happens .......

Command Receivers

These are among the easiest receivers in the surplus market to get running.
If the dynamotor-mount power supply is used, BFO and gain controls plus a phone
jack must be added. These can be brought out the front from the adapter well
connector (Don't forget to keep pins 6 & 7 jumpered or the tubes don't get
nice and warm!) although an extra wire for the receiver audio will have to be
pulled to an unused pin. Alternatively they can be brought out the rear
connector without any changes. The gain control is a simple 50k-ohm pot to
ground and the BFO control is a SPST switch to ground with the closed position
being 'OFF'.

While a phone jack is still need (and easily added), capturing a C-24 or
FT-260 local control adapter makes all this bunches easier. If one isn't handy,
a little careful layout can be used to make one from a remote control adapter.
By squeezing a bit and careful parts selection, a phone jack can be added thus
going A.R.C. one better!

If a local tuning knob isn't available, a radio-TV push-on knob, a piece of
tubing pressed over the spline, or whatever else you can find that will turn the
shaft is just fine for tuning. If you can get a piece of shaft with one good end
(or just the ends from a shaft kit) then a knob can be fitted to the end of the
inner piece and locked in place like the local knob is. The bottom line is 'Use
whatever works for you.'

One note- All the sets I've had were wired for 600 ohms, how- ever some of
the early units had a high-impedance tap as well. It may be wise to check your
radio to see how it's wired if you have one of them.

The LF (.19-.55 MHz) receivers make nice add-on units for receivers having an
IF in that range and are suffering from a lack of sensitivity. Simply wrap a
piece of insulated wire around the input lead to the grid of the first IF stage
and connect the other end to the antenna post if the LF receiver. Tune the LF
receiver to the IF of the other, fire up both and listen on the audio output of
the add-on. The selectivity can be sharpened by removing the covers form the IF
cans on the LF unit and pulling the fiber rods up. Don't get too 'dedicated to
this process though- there is a stop and the rods do break! The selectivity can
be set by adjusting the rods to suit your needs, although all the way up is
beautiful for CW. This operation is known as a 'Q-5er* and has been around for
quite a while. But, old as the process is, it still works very nicely.

Type 12 Receivers

These are about the same to convert as the Command sets with the only
complication being the lack of a dial. This has been covered by Fair very nicely
in the form of a BC-473 control box fitted with an adapter to mount on the front
of the receivers. This has the advantage that a gain control plus a switch that
can be used for the Audio Hi-Lo control on the VHF units are already on the box.

To use the rear-mounted power supply, pins A & E of the top connector
have to be tied together to get B+ from the power supply to the receiver. The
BC-473 controls can be used by connecting the lower right-hand receptacle to the
one on the box- pin A to 2, C to 4, and E to 3. By connecting pin B to 7 and
putting a 1000 ohm resistor from pin 7 to ground in the box or pin B to ground
in the receiver (leaving the other wiring on the pin used intact) the Audio
Hi-Lo circuit will work. Otherwise, pin B must be grounded. Hi audio will be
with the BFO control in 'MCW'. A little paint, patience and a signal source will
handle the dial re-calibration although for the R-11 it's not necessary.

To use the Fair unit, remove the wire from pin F of the lower right connector
and move the wire from pin E of the upper one down to the pin just emptied. This
puts the receiver B. on the lower connector and allows it to be used for
everything. Using the pin-out for this connector (remembering the change just
suggested) and the one for the rear of a Command receiver, the cable from the
power/control unit can be modified to work with these receivers. The Audio Hi-Lo
line will still need the 1000 ohm resister.

The R-11 can be used as a ~-5er however the main receiver's BF0 will have to
be used since the Type 12's don't have one. Alternatively, one could be
installed using the parts and circuit from a Command receiver or a semiconductor
circuit could be added to handle this. Some squeezing may be necessary, but use
your imagination.

Other Receivers

Using the R-13 is sort of a cross between the Command boxes and the Type
12's. To get power and control to it, the rear connector has to be used, however
the tuning is like the Type 12'e. While either power supply mentioned before can
be used, the Fair unit is mere practical since the other requires set
modification to get the controls and audio output in. There is room on the front
for the pot and jack so if this is what you want there's no problem there. Note
that if the R-445 is being used, pins A & E of the front connector have to
be jumpered to get B+ to the receiver if the rear-mounted power supply is being
used.

The R-20 is easy.., it's fixed tuned at 75 MHz and, unless one likes
listening for marker beacons, requires some pretty bag modifications to use.
This is a good one to play with since there is potential in it to be something
else, although the only thing that comes to mind is a monitor for some favored
frequency like on 6 meters which isn't that too awful far away.

The R-22 likewise is easy, but for a different reason. This set is much like
the R-10 but with only one instead of three receptacles. By following the
pinouts, everything mentioned on the Type 12 sets applies to this one as well.

A real challenge is presented by the R-34. This unit uses a motor driven
crystal select system to tune to the desired frequency. (It also requires that
the low voltage be dc and not ac.) Since, to select the proper frequency, it
uses 10 wires in a non-redundant code (five each for MHz and tenth MHz) the
original control box is necessary. There are three squelch options- none (pin F
of either front connector grounded), internal(Jumper between pin E and pin F of
the big receptacle, J-2) or external (a 100k ohm pot to ground from pin F of
either receptacle. ) Gain and audio are handled as in the Type 12 receivers.

One of the newer A.R.C. receivers to hit the market is the R-836/ARN-59. This
is a modernized ARN-6 or LM-26 and is smaller and lighter than either of those
anchors. Power is easy- +24v at about 1-1 1/2 amps and +110 & +125v for B+.
The latter may, without any major detriment, be tied to the +110v line thus
simplifying the power supply. The volume control is a 100k ohm pot with one end
grounded, the other tied to the AF Plate lead, and the tap to the AF Grid line.
The RF sensitivity control is a 50k ohm pot to ground, or the line may be
grounded directly. Like the Command sets, the BFO control is grounded to turn
the BF0 off. Band selection is by grounding the proper pin. For just listening,
pins D,I,M,N,O, Q, & R may be ignored.

The original control box is suggested for this unit not only for the controls
but for the three-band dial. A little ingenuity and some tin-bending can be used
to make a false front for the receiver to mount the control box as well as the
phone jack, thus making a neat, compact unit.

Command Transmitters

Like the Command receivers, these are very easy to get working in their
original form, and accept modification very nicely. They make neat little
single-band rigs that will load practically any- thing with a short wire (up to
50') being their 'specialty'.

The power needed is 24v mt about 1« amps (filtered dc if the relays are to be
used), around +200v at about 10ma of stiffly regulated dc for the oscillator B+,
250v at around 15ma for the P.A. screens and up to 600v at up to about 200ma for
the P.A. B+.

Keying the 'Select' line will result in full break-in operation since the
select relays connect the oscillator to its B~, ground the P.A. cathodes, and
attach the output to the antenna. This gets noisy for a home environment,
although in a prop-driven bomber, no one seemed to notice. Tying the Osc. B+
directly to the oscillator, and the cathodes to a key jack will result in a
quieter operation, although break-in is no longer possible. An rf choke should
be put between the cathodes and the jack, and bypass caps (.01 to .001uf at 1
kv) on both ends of the choke. There's very few 'bad habits' in these rigs
(click, chirp, etc) and those that are present may be cleaned up by normal
techniques.

Tune-up is simple. Tune to the desired frequency, apply high voltage, and
tune the loading & coupling controls for maximum output. An antenna relay's
handy here- the output meter's on it.

The 4-5.3 MHz transmitters will go down to 80 meters by closing the cap under
the cover between the P.A. tubes and the rest. Like- wise the 5.3-7 MHz boxes
will go to 40 meters by opening the cap, or by lopping a few turns off the
oscillator coil, as you may wish. In both cases, the dial will have to be
recalibrated and the P.A. 'fixed' cap will have to be re-adjusted for maximum
output. The tracking won't be as good, but over short segments (like the Novice
sub-bands) it's close enough that re-trimming isn't needed. A short extension
and knob can be put on the cap's shaft to juggle it if you like, but if the
initial tune-up is in the center of the band, then it shouldn't be needed for
narrow segments.

In the cathode keyed version, there's a slight drift in the oscillator.
Typically, mine have slipped down about 100 cycles in around 10-20 minutes then
stayed put. I haven't tried relay keying however it may be more stable since the
oscillator tube never really gets a chance to get hot like it does on keying the
P.A. cathodes.

By removing the 'eye'-tube and the calibration crystal, there is enough room
to add practically anything you'd like to build in. Buffers, multipliers,
keyers, and a whole bunch more have at one time or another been put in, so have
fun. This is an excellent 'imagineering' machine.

Type 12 Transmitters

These little boxes, like the Command transmitters, are pretty neat by
themselves or as the basis for projects. They run from the same supply as the
Type 19 receivers and are very easy to use as is for local rag-chewers, although
they are AM units.

The T-13 hits 2 meters directly however the T-11 misses by a bit. This can be
easily fixed by lopping a few turns off of the tuned circuit coils and replacing
the 50pf cap on the oscillator tank with a 35Pf one. Note that these
transmitters double in the final which can lead to extensive official
correspondence that's really not pleasant. This can be avoided by careful tuning
and/or a filter in the output circuit...with the preferable choice being both.
The units will operate over a 2 MHz bandwidth without re- tuning which is rather
convenient considering the current band arrangement.

The low voltage has to be dc and well filtered. The relays use this, but can
be defeated. However the mic. circuit also uses this to get dc to the mic. (They
use carbon mic's) and, unless you like hum on your audio or convert to another
input circuit, this makes filtering a 'must do'

The basic hook-up is simple-wedge a channel relay closed and plug in a
crystal (6 or 8 MHz) for the proper frequency, plug in a mic., put power on the
appropriate pins and you're in business.

Using these with the R-19 is equally easy. If the rear-mount power supply is
being used, connect the top receptacle of the receiver to the 6-pin on the
transmitter pin for pin.(Pin F can be omitted.) With the outboard supply, the
only difference is that pin A on the transmitter will go to the power supply +HV
output and pin E will go to pin E of the upper or pin F of the lower receptacle
dependant on whether or not the receiver was altered as previously discussed.
For frequency selection, relays can be wedged, relays can be removed and a 5 (or
more) position rotary switch installed in their place, or they can be operated
as they were intended.

The T-11 unconverted and a low power HF SSB rig can become the basis for a 2
meter SSB rig with the T-11 providing the VHF input to a mixer, Likewise the
T-13 (or a converted T-11) can drive a DSB power amp, for 'almost SSB'. The
possibilities are endless.

While these units were designed for AM, that mode of operation is slowly
disappearing (darn it). However there's nothing saying they can't be used for CW
or, by modulating a varactor (or by some other method,) FM. Like the Command
transmitters, these are nice basic units that leave a lot of room to play in.

Other Units

For local rag-chewing on 220 MHz, the TV-10 (a.k.a. CV-431/AR) is a very nice
basic unit. As is it works with an R-19, but won't quite hit 220 without some
minor alteration.

The receiving converter has no rf stage, just a band-pass filter followed by
a mixer. The local oscillator is at ll0 MHz and uses the 7th overtone of the
crystal, The transmitter triples in the final, which (like the Type 12's)
implies careful tuning and filtering to cure any 'bad habits'. Like the Type
12's, this is a good 'project starter' unit.

Using the transmitter is just like on the Type 12 boxes- put in a crystal,
plug in a mic., put power to it and let 'er rip. The 108-136 MHz receivers will
work with the converter with the original ll0 MHz local oscillator however the
bottom couple hundred kHz will be covered up by the oscillator. One way around
this is to use a 100 MHz 1.o. and either frequency range receiver (the input
will be the dial plus 100, which is handy) or use a different over- tone of the
oscillator. (I've seen one reference that says this works without any surgery
and another that says it doesn't: All I can suggest is that you try...it can't
hurt')

The TV-10 and the R-19 (or other receiver) will fit the Command receiver
racks nicely with only minor modification. The TV-10 and Type 12's require that
the mounting angle on the front of the receiver be removed and some 'points'
like on the Command and Type 15 receivers be mounted in the outboard holes from
the angle mounting screws. (A couple of screws mounted so they stick out far
enough that the locking 'ears' can grab them will also work.) The receptacles at
the rear of the rack bays have to be removed, or rewired in the case of a Type
15 receiver. The boxes will now slide in and lock into the rack bays like they
were designed to do it.

By installing a stop in one bay of a three-bay rack, a VHF transmitter
(properly equipped with 'points') can be mounted in addition to the above set-up
making a very nice, neat VHF/UHF installation for local work. It can be tucked
into a corner and remote controlled more or less as designed with very little
effort. A slightly rewired C-56 will do very nicely for the control side with a
small panel added to handle to audio and/or key jacks.

If you have no serious objections to 50 kHz crystal-controlled channel
spacings, the RT-524M is a very sweet little rig. Only needing about 6 amps of
+24v power, this is a quick way to get on 2 meters AM with no bad habits. Crank
the power into the switched or unswitched inputs and the amplifier input,
hook-up a mic and some phones, put an antenna on it and it works.

Close examination of the antenna connectors in back will reveal that one's
not tied to anything...and it mates to the other. By removing the 'dummy' and
soldering a piece of coax to it gains you an instant match to an uncommon
connector. (How often dc you find unusual connector that come with their own
mates these days?)

This rig has a really cute feature, that being that the audio amp may be run
independently from the rest of the radio. The 'RT- 524' input comes from the
phone output of the radio. The auxiliary inputs can come from up to four other
radios, and go, with the 'RT- 524' input to a resistive mixer, then to the audio
amp. This is rather nice when one has a multi-radio installation and only wants
one audio source to jack into...just like in an airplane.

While moving the transmitter around without a new crystal bank is tough, the
receiver can feed a tunable IF (like a Command 1.5-3 MHz receiver) since the
final IF is 2 MHz. This will allow between the channel listening as well as give
a BFO should CW be desirable. The transmitter may be FMed by the 'modulated
varactor' or any other method you like, or may be used as the driver for a DSB
power amp. Again, it is a good unit as is or as the starter for a bigger
project.

SOME RANDOM NOTES

The foregoing has been the just the briefest outline of what can be done with
these units. Detailed conversions have been avoided since they are up to the
users and no two will want to do the same things or have the same 'junk boxes'.
Research (another word for raiding the magazine shelf or the memory of a ham who
has been in the game for a while!) will reveal a few more and probably answer
any points you may have on these sets. In any event, experiment. Play with the
boxes and enjoy them They Are Fun.

The voltages shown for the Command receiver B+ and the P.A. B+ for the
Command transmitters are maximums. Going above them is likely to result in some
rather unusual odors as components express their displeasure at the excess. The
Type 12 and 15 units can go a bit higher, around 275-285 volts, but above that
get very shaky. On the other hand, the Command receivers will still operate with
as little as 100 volts of B+ and the transmitters will go down to about 250
volts and still work (with attendant reduction in the screen voltage,
naturally!)

While everything presented has been aimed more or less at the amateur, there
are other uses. The LF receivers can be used to monitor the weather reports on
the aviation beacons in that range and I suspect will tune down to the 160-190
kHz band without too much bending. The VHF receivers may be used to monitor air
traffic since they are COM or NAV/COM units. If one has an RT-524A, it may still
be useable in aircraft (the question being in the type certification) but as a
360 channel monitor it's very nice. The high- altitude en-route traffic can be
hit the same way as discussed in the section on the RT-524M- i.e., with a
tunable IF to cover the new 25 kHz channels.

Military air traffic can be monitored with a TV-l0 and an R-19 if you're
close to an installation. The lack of an rf stage makes for not so very good
sensitivity so coverage over any appreciable distance is not too likely.
Foreknowledge of the local frequencies is a must, as is patience. Military
transmissions are brief and infrequent...or they're supposed to be.

The Fair type 818 transformer is being (or has been) replaced by a new and
more versatile one. This is the number XM-108 trans- former, which has a center
tap on the 24 volt winding plus a 6 volt winding as well. This allows the 12
volt radios to be used with the same transformer by a simple power supply
alteration. The new one is shown in the drawings following this section.

There are other uses for the sets. As I said before, the limiting factors are
budget, junque-box, and imagination.

Enjoy.